Bus pinout¶
The CubeSat Kit bus runs through every module on two 2×26 headers, H1 and H2.
These are the names CSK_Bus gives its pins, laid out as the header: odd
pins in one row, even pins in the other. In the symbol and footprint, H1 is
pins 1 to 52 and H2 is pins 53 to 104, so H2 pin n is symbol pin n + 52.
H1¶
| H1 pin | Signal | H1 pin | Signal |
|---|---|---|---|
| 1 | IO.23 |
2 | IO.22 |
| 3 | IO.21 |
4 | IO.20 |
| 5 | IO.19 |
6 | IO.18 |
| 7 | IO.17 |
8 | IO.16 |
| 9 | IO.15 |
10 | IO.14 |
| 11 | IO.13 |
12 | IO.12 |
| 13 | IO.11 |
14 | IO.10 |
| 15 | IO.9 |
16 | IO.8 |
| 17 | IO.7 |
18 | IO.6 |
| 19 | IO.5 |
20 | IO.4 |
| 21 | IO.3 |
22 | IO.2 |
| 23 | IO.1 |
24 | IO.0 |
| 25 | -FAULT |
26 | VREF0 |
| 27 | SENSE |
28 | VREF1 |
| 29 | -RESET |
30 | VREF2 |
| 31 | OFF_VCC |
32 | +5V_USB |
| 33 | PWR_MHX |
34 | -RST_MHX |
| 35 | -CTS_MHX |
36 | -RTS_MHX |
| 37 | -DSR_MHX |
38 | -DTR_MHX |
| 39 | TXD_MHX |
40 | RXD_MHX |
| 41 | SDA_SYS |
42 | VBACKUP |
| 43 | SCL_SYS |
44 | RSVD0 |
| 45 | RSVD1 |
46 | PPS |
| 47 | USER0 |
48 | USER1 |
| 49 | USER2 |
50 | USER3 |
| 51 | USER4 |
52 | USER5 |
H2¶
| H2 pin | Signal | H2 pin | Signal |
|---|---|---|---|
| 1 | IO.47 |
2 | IO.46 |
| 3 | IO.45 |
4 | IO.44 |
| 5 | IO.43 |
6 | IO.42 |
| 7 | IO.41 |
8 | IO.40 |
| 9 | IO.39 |
10 | IO.38 |
| 11 | IO.37 |
12 | IO.36 |
| 13 | IO.35 |
14 | IO.34 |
| 15 | IO.33 |
16 | IO.32 |
| 17 | IO.31 |
18 | IO.30 |
| 19 | IO.29 |
20 | IO.28 |
| 21 | IO.27 |
22 | IO.26 |
| 23 | IO.25 |
24 | IO.24 |
| 25 | +5V_SYS |
26 | +5V_SYS |
| 27 | VCC_SYS |
28 | VCC_SYS |
| 29 | DGND |
30 | DGND |
| 31 | AGND |
32 | DGND |
| 33 | S0 |
34 | S0 |
| 35 | S1 |
36 | S1 |
| 37 | S2 |
38 | S2 |
| 39 | S3 |
40 | S3 |
| 41 | S4 |
42 | S4 |
| 43 | S5 |
44 | S5 |
| 45 | VBATT |
46 | VBATT |
| 47 | USER6 |
48 | USER7 |
| 49 | USER8 |
50 | USER9 |
| 51 | USER10 |
52 | USER11 |
The groups¶
| Signals | Pins | What they are |
|---|---|---|
IO.0 to IO.47 |
H1.1–24, H2.1–24 | General-purpose I/O. What each carries (SPI, UARTs, GPIO, analog) is set by the module that drives it. |
+5V_SYS, VCC_SYS |
H2.25–28 | System power: +5 V and VCC (normally +3.3 V). |
DGND, AGND |
H2.29, H2.30, H2.32; H2.31 | Digital and analog ground. |
VBATT |
H2.45–46 | Battery voltage. |
+5V_USB, VBACKUP, PWR_MHX |
H1.32, H1.42, H1.33 | USB power, backup (RTC) battery, transceiver power. |
S0 to S5 |
H2.33–44 | Remove-before-flight and separation switch terminals, two pins each. |
SDA_SYS, SCL_SYS |
H1.41, H1.43 | The system I²C bus. |
-FAULT, SENSE, -RESET, OFF_VCC, PPS |
H1.25, 27, 29, 31, 46 | Control and status. |
VREF0 to VREF2 |
H1.26, 28, 30 | Analog references. |
-RST_MHX to RXD_MHX |
H1.34–40 | The radio transceiver interface. |
USER0 to USER11 |
H1.47–52, H2.47–52 | User-defined. |
RSVD0, RSVD1 |
H1.44, H1.45 | Reserved. |
A name is the bus's, not the module's
The names are the bus definition. A module may use a pin differently:
Pumpkin's EPS Module 1, for one, puts battery and +12 V power on some
S0–S5 and USER pins. Check each module's datasheet for what it
actually puts on a pin before wiring to it.
Sources¶
The table is tools/csk_bus_pins.csv, from Pumpkin's Motherboard Module
(MBM) 2 datasheet,
710-01362 rev E
(December 2017). Its connector drawing and its pin description tables agree,
and Pumpkin's EPS Module 1 datasheet,
710-01952 rev C
(February 2023), agrees wherever it gives the bus name.
The older CubeSat Kit FM430 Flight Motherboard datasheet,
710-00484 rev D
(September 2009), differs in two places. Its pin table puts VREF1 on H1.30
and VREF2 on H1.28, against its own connector drawing; and it names H1.46
RSVD2, which later sheets call PPS. The table follows the later sheets.