GPIO pinout¶
What each of J1's 40 pins is, and what the template connects it to. This table is written from the template's own schematic each time the site is built.
| Pin | J1 pin name | Template | Pin | J1 pin name | Template |
|---|---|---|---|---|---|
| 1 | 3.3V | +3V3 |
2 | 5V | +5V |
| 3 | BCM2_SDA | label GPIO2 |
4 | 5V | +5V |
| 5 | BCM3_SCL | label GPIO3 |
6 | GND | GND |
| 7 | BCM4_GPCLK0 | label GPIO4 |
8 | BCM14_TXD | label GPIO14 |
| 9 | GND | GND |
10 | BCM15_RXD | label GPIO15 |
| 11 | BCM17 | label GPIO17 |
12 | BCM18_PCM_C | label GPIO18 |
| 13 | BCM27 | label GPIO27 |
14 | GND | GND |
| 15 | BCM22 | label GPIO22 |
16 | BCM23 | label GPIO23 |
| 17 | 3.3V | +3V3 |
18 | BCM24 | label GPIO24 |
| 19 | BCM10_MOSI | label GPIO10 |
20 | GND | GND |
| 21 | BCM9_MISO | label GPIO9 |
22 | BCM25 | label GPIO25 |
| 23 | BCM11_SCLK | label GPIO11 |
24 | BCM8_CE0 | label GPIO8 |
| 25 | GND | GND |
26 | BCM7_CE1 | label GPIO7 |
| 27 | BCM0_ID_SD | EEPROM ID_SD |
28 | BCM1_ID_SC | EEPROM ID_SC |
| 29 | BCM5 | label GPIO5 |
30 | GND | GND |
| 31 | BCM6 | label GPIO6 |
32 | BCM12_PWM0 | label GPIO12 |
| 33 | BCM13_PWM1 | label GPIO13 |
34 | GND | GND |
| 35 | BCM19_MISO_PCM_FS | label GPIO19 |
36 | BCM16 | label GPIO16 |
| 37 | BCM26 | label GPIO26 |
38 | BCM20_MOSI_PCM_DI | label GPIO20 |
| 39 | GND | GND |
40 | BCM21_SCLK_PCM_DO | label GPIO21 |
The J1 pin names are BCM GPIO numbers with a common alternate function
(BCM2_SDA); which functions a pin actually has depends on the Device Tree
overlay your design uses. pinout.xyz shows them all.
Using a pin¶
Each free GPIO pin carries a global label named for its BCM number. To use
a pin, place a global label of the same name, such as GPIO17, on the part it
connects to, in any sheet. The J1 sheet itself never needs editing.
- A global label joins every label of that name in the design, so do not reuse
GPIO2toGPIO27for anything else. - Until a label is used elsewhere, ERC reports it as
isolated_pin_label, a warning. Each warning disappears as its pin is used. - Rename a label, if you prefer a functional name, on J1's sheet; keep the pin it sits on.
Pins to know about¶
- ID_SD and ID_SC (pins 27 and 28) are the ID EEPROM's and nothing else's.
- GPIO2 and GPIO3 (pins 3 and 5) have about 2 kΩ pull-ups to 3.3 V on the Pi itself, so they idle high.
- GPIO6, GPIO14 and GPIO16 may be driven as outputs at boot by very old firmware that mistakes a newer Pi for a Model B. Raspberry Pi's design guide asks boards that also drive these pins to protect against it, for example with a series resistor.