lever-nut-holder-scad
A printable holder for WAGO 221 lever connectors, made in OpenSCAD. Each connector sits in its own slot, held down by a lip over its back edge, with the front left open for the wires and the levers free to open. Lay out any mix of 2-, 3- and 5-conductor connectors in one row or two back to back, lying flat or standing up, with a screw tab at each end.

Use it
Open lever_nut_holder.scad in OpenSCAD and set the
parameters in the Customizer panel:
blocks_config: one entry per slot, the number of conductors on the connector that goes in it: 2, 3 or 5 for the 221-412, 221-413 and 221-415.[5, 3, 2]is one of each.style_config:horizontal: one row lying flat; the wires leave sideways.horizontal_mirrored: two rows back to back, sharing the back wall.vertical: one row standing on its back wall; the wires leave upward.vertical_mirrored: two rows standing up, sharing the floor.
- Screw tabs:
tabsturns them on or off;tab_width,tab_radiusandtab_heightset their size, the hole and their thickness. The default hole is 5.2 mm across. allowance: the clearance added to each connector’s width, depth and height, 0.2 mm by default.

To use it from another design, put this folder in your OpenSCAD library folder and call the module:
use <lever-nut-holder-scad/lever_nut_holder.scad>
lever_nut_holder(blocks = [5, 3, 2], style = "vertical", tabs = false);
lever_nut_holder() takes blocks, style, tabs, tab_width,
tab_radius, tab_height and allowance, with the same defaults as the
Customizer. It refuses an unknown style, an empty or fractional blocks, and
a screw hole as wide as its tab, with a message saying which.
Fitting the connectors
Tip a connector’s back edge under the lip, then press the front down past the low front stop. To take it out, lift the front over the stop and slide it forward.
The slots are sized from WAGO’s datasheets: 18.6 mm deep, 8.3 mm high, and
13.1, 18.7 or 29.9 mm wide for 2, 3 or 5 conductors (5.6 mm a conductor, plus
1.9 mm). The lip sits allowance above the top of the connector. If the
connectors rattle, lower allowance; if they won’t go in, raise it.
Known limits
- It hasn’t been test-printed yet. The checks below prove the slots clear a connector at datasheet size and that the lip reaches over it, not how it feels on a real 221 printed on a real printer, or whether the levers swing fully open under the lip.
- Only the 221 series with levers on top. The inline 221-2411 and the 221-6xx connectors have other sizes.
Checks
just test takes about 2 s. It renders each case with warnings treated as
errors:
- Every style, with tabs on and off, and four other layouts: one solid, of the size worked out by hand, sitting at the origin.
- Every style with five layouts:
- Fit: where the holder meets connectors at datasheet size is empty.
- Grip: where it meets connectors 1 mm taller is one piece of lip for each connector.
- The four refusals, each with its message.
just images renders the two pictures in this README. Written against
OpenSCAD 2026.10.15.
Origin and licence
The holder is a rewrite, under MIT, of an idea from Joo Chung’s WAGO 221 mounts on Thingiverse: a row of slots for lever connectors with a screw tab at each end. The code and the slot design are new, sized from WAGO’s datasheets; the Customizer parameters keep their names. This repository’s earlier versions were modifications of Joo Chung’s design and are in its history; that design is under CC BY-NC-SA 4.0. MIT; see LICENSE.
WAGO is a trademark of WAGO GmbH & Co. KG. This project isn’t affiliated with WAGO.