Ergonomic Handle

An OpenSCAD library that generates an ergonomic handle, one that spreads hand contact pressure as evenly as possible, scaled to any hand size.

Ergonomic Handle V5 Render

It continues Alex Matulich’s “Ergonomic handle based on scientific study” (Thingiverse, Printables).

Basis

The dimensions come from several research papers using anthropometric data from populations around the world. The profile comes from a 2020 study in which gripping hands were measured with a contour gauge to derive the curves of an ergonomic handle. The studies are cited and linked in Alex’s article “Whose hands are biggest? You may be surprised.”

The contour study is generalised to any hand: the handle’s height follows metacarpal breadth (hand width) and its cross-sections follow hand length, so the study’s curve control points can be scaled vertically and horizontally to fit.

3D Printed Grooved Handle

Usage

Put ergonomic_handle.scad where your script can find it, such as beside it:

use <ergonomic_handle.scad>

ergonomic_handle(hand_length = 178, hand_width = 79.4, bottomcapext = 6, groovespc = 6);

Opening ergonomic_handle.scad itself shows a handle driven by the customizer; ergonomic_handle.json holds presets for it, and ergonomic_handle.csv lists the same designs one per row for batch export.

Modules

ergonomic_handle(...)

Renders the handle body. The centre of the top surface is at the origin and the bottom, not counting the bottom cap, is ergonomic_handle_height() below it.

OpenSCAD Render

Parameter Default Meaning
hand_length 186 Tip of the middle finger to the first wrist crease, in mm.
hand_width 85 Metacarpal breadth: width of the four fingers where they meet the palm, in mm.
flair true Flare the top and bottom of the front edge for better pull force. false gives the handle as the study describes it.
bottomcapext 0 Bottom cap extension in mm; 0 is a flat bottom. Suggested: 3 to 8.
topext 0 Extend the curves upward by this many mm, above the origin.
groovespc 0 Spacing of grip grooves in mm; 0 is none. Suggested: 6 to 10. Ignored when fingergroove is on.
fingergroove false Add finger grooves. The handle then fits only the hand it was sized for and is uncomfortable for others.
tiltangle 110 Handle tilt in degrees. No less than 90.
fn 64 Facets around the cross-section and, without finger grooves, vertical slices. With finger grooves there are always 128 slices.
halfrotate false Rotate the cross-section’s vertices by half a segment. Useful for overlapping two low-facet handles into a texture.
metacarpal_expansion 1.12 How much metacarpal breadth grows in a grip. Values outside 1.10 to 1.15 are clamped to that range, with a warning.
groovedepth 0.6 Depth of the grip grooves, in mm.
bottomcapscale 0.3 Scale of the last cross-section of the bottom cap.

ergonomic_handle_top_ellipse(...)

A 2D polygon matching the top surface of the handle, including topext. Takes hand_length, hand_width, metacarpal_expansion, flair, fingergroove, topext, tiltangle, fn and halfrotate, with the same defaults as ergonomic_handle. Pass the same values to both.

ergonomic_handle_bottom_ellipse(...)

A 2D polygon matching the bottom surface of the handle, not counting the bottom cap. Useful for matching something to a handle without a cap. Same parameters as the top ellipse, without topext.

ergonomic_handle_height(hand_width, metacarpal_expansion)

The height of the handle body without extensions: hand_width times metacarpal_expansion, the latter clamped as above. Defaults to 85 and 1.12.

default_hand_length(female) and default_hand_width(female)

The average hand: 186 by 85 mm, or 171 by 76 mm with female = true.

Hand sizes

The defaults were calculated from journal data broken down by nationality: Bangladeshi, Czech, Filipino, German, central Indian, East Indian, Iranian, Korean, Jordanian, Mexican, Taiwanese, Turkish and Vietnamese. The average male hand is 186 mm long (range 173 to 198) and 85 mm broad (range 78 to 98). The average female hand is 76 mm broad (range 68 to 92), with lengths from 161 to 180 mm. The average male size should also suit nearly all adult women and all children.

Examples

  • examples/handle_no_grooves.scad: a plain handle.
  • examples/grooved_handle_with_extension.scad: grip grooves, a top extension, a bottom cap and a structure built on the top ellipse.
  • examples/low_facet_handle_with_grooves.scad: two low-facet handles overlaid for texture.

Printing

Handle on Printer Build Plate

Print the handle upside-down and it needs no supports. Settings that have worked: a Prusa i3 MK3S with 15% gyroid infill.

Development

With just, OpenSCAD and Python 3 installed, just test renders the library, every example and every preset with OpenSCAD warnings treated as errors.

License and attribution

Creative Commons Attribution 4.0 International. See LICENSE.

The design is by Alex Matulich, version 5.1 of May 2022, published on Thingiverse and described on his blog. The header of ergonomic_handle.scad notes the changes made here in November 2026.

Ergonomic Handle Design


This site uses Just the Docs, a documentation theme for Jekyll.